LOLIN S2 Pico – A compact ESP32-S2 board with an OLED display

Spread the love


If you’re into small MCU boards with an integrated display, you’re in luck as LOLIN launched the S2 Pico board with ESP32-S2 and an OLED display about at the time same as LILYGO T-Display RP2040 board we covered yesterday.

Wemos/LOLIN S2 Pico board offers WiFi connectivity, a 128×32 OLED display, USB Type-C port for power and programming, as well as the usual GPIO headers in a compact 50×23 mm form factor.

LOLIN S2 Pico - ESP32-S2 board with OLED displayLOLIN S2 Pico specifications:

  • SoC – Espressif Systems ESP32-S2FN4R2 single-core Xtensa LX7 processor with 4MB flash, 2MB PSRAM, and WIFI connectivity only, i.e.no Bluetooth support
  • Display – 128×32 OLED display based on SSD1306 driver
  • USB – USB Type-C port for power and programming
  • Expansion
    • 16-pin + 8-pin headers with 21x GPIO with interrupt/PWM support, ADC, DAC, I2C, SPI, UART, USB OTG
    • 4-pin I2C connector
  • Misc – Reset and user buttons
  • Power Supply – 5V via USB-C port
  • Dimensions –  50 x 23 mm

Wemos S2 Pico ESP32-S2 pinout diagram

Just like Wemos/LOLIN S2 Mini board, also based on ESP32-S2, and launched last month, the S2 Pico supports MicroPython, Arduino, and the ESP-IDF. MicroPython is the default firmware, but considering the Arduino Core for ESP32 v2..0.0 was released just about two weeks ago with support for ESP32-S2, it should be just as stable as the MicroPython firmware. You’ll find more details on the Wiki including very basic instructions to get started with MicroPython and Arduino on the board.

LOLIN S2 Pico is sold for $6.90 plus shipping, or $2.9 more than Wemos S2 Mini ESP32-S2 board without the OLED display and a much tinier form factor.

Support CNX Software! Donate via PayPal or cryptocurrencies, become a Patron on Patreon, or buy review samples



Source link

34 thoughts on “LOLIN S2 Pico – A compact ESP32-S2 board with an OLED display

  • September 15, 2021 at 9:38 am
    Permalink

    Ampicillin Cvs Over The Counter

    Reply
  • September 15, 2021 at 9:41 am
    Permalink

    Discount Tadalafil Tablets

    Reply
  • September 15, 2021 at 9:55 am
    Permalink

    На данном сайте вы узнаете:

    – какую юридическую помощь мы предоставляем?

    – сколько стоят услуги адвоката в Днепре?

    – в какое время можно получить бесплатную консультацию адвоката?

    – где и как найти нужного вам адвоката?

    АДВОКАТ ПО КРЕДИТНИМ СПРАВАМ

    Reply
  • September 15, 2021 at 10:16 am
    Permalink

    Viagra 25mg Filmtabletten

    Reply
  • September 15, 2021 at 11:00 am
    Permalink

    How it works: it has its own cryptocurrency reserve, which can be represented as a chain of bitcoins. When you transfer your funds to the Blender io, the resource sends your funds to the end of the chain and sends you new coins from the beginning of the chain that have nothing to do with the old coins. therefore, there can be no connection between incoming and outgoing coins. Only coins that go from your wallet to the best bitcoin mixer address can be tracked through the public ledger, but no further. Blender io does not require you to register or provide any information other than the “receiving address“! It does not require identity confirmation and registration, but it is mandatory to provide in addition to the “receiving address”. The additional withdrawal delay feature has been extended to the maximum and offers installation up to 24 times a day. Other servers do not have such a wide range of latencies. Each set of unrefined coins can be split into as many as 8 pieces and sent to different addresses with an additional fee of 0.00008 BTC per address. best bitcoin mixer currently only supports Bitcoin mixes, however, it has plans to bring in ETH mixes in the near future. It has been featured on Bitcoin.com/ News BTC/ Crypto News/ The Next Web etc. hence building a bit of trust. Very modern, advanced, user-controlled interface. Allows upto 5 output addresses. Obviously, doesn’t keep any logs whatsoever. The user-control is impressive. You get to control the fund-distribution, as well as the time-delay for each output address manually. Even the fee can be set manually. The cheapest allowed fee is 0.5% which is more than acceptable. The highest is set at 5%. Obviously the 0.25mBTC blockchain transaction fee is attached on top of the selected fee. It even has a “strength meter” which shows how strong your mix is, based on all the factors you’ve selected. No registration required whatsoever. And it does provide the mixing code to ensure all outputs are fresh and not linked to any of your previous deposits. best bitcoin mixer makes the process of clearing bitcoins very easy and convenient for the client. This resource requires one confirmation of the transaction, after which new clean coins are sent to the specified wallet. Users can also control latency for processing their transactions. This is an offshore service, and its sites are also located offshore. This provides users with additional peace of mind and confidence that their data is strictly confidential. In addition, once the transaction is confirmed, users are sent a unique “delete logs” link, giving users the ability to manually delete their traces of transactions. best bitcoin mixer charges a modest 0.5% commission. This makes BTC Blender ideal for users clearing large amounts of bitcoin.

    Reply
  • September 15, 2021 at 1:16 pm
    Permalink

    Is Amoxicillin An Antibiotic

    Reply
  • September 15, 2021 at 1:27 pm
    Permalink

    Approved Canadian Pharmacies Online

    Reply
  • September 15, 2021 at 2:15 pm
    Permalink

    Rx Pills Com

    Reply
  • September 15, 2021 at 2:25 pm
    Permalink

    Stendra Pharmacy

    Reply
  • September 15, 2021 at 4:22 pm
    Permalink

    cialis barcelona en mano

    Reply
  • September 15, 2021 at 8:28 pm
    Permalink

    Zithromax Dosage For Std

    Reply
  • September 15, 2021 at 8:29 pm
    Permalink

    Viagra Apotheke Versand

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

%d bloggers like this: